ANVIL CLAMP VISE—Specially suited to laboratory shops, has small space for anvil work, clamps to table. Best low priced combined anvil and vise. Width of jaw 4½ cm. opening 4 cm. clamps table tops up to 2 cm. thickness. Be sure to what we think are the best bench vise for the money as of 2022.
BRACE, Ratchet Bit, Stanley—With concealed ratchet, knurled chuck, alligator pattern jaws and ball-bearing, half steel clad, cocobolo head. Nickel plated. 10 inch sweep.
BITS, Auger, Irwin Set—Set of 13 genuine Irwin solid center auger bits, 32½ quarters. One each, 4,5,6,7,8,9,10,11,12,13,14,15 and 16/16ths. On board rack, providing a convenient arrangement for ready use. We also . have a list of the best auger drill bits for the modern era.
BITS, Auger, Russell-Jennings—Forged from tool steel, oil tempered. Polished twist and shank. Double extension lips and cutters. Double thread on screw. Average length of twist, 4½ inches. Average length over all, 8½ inches.
CHISEL AND PUNCH SET—Consists of 12 octagon chisels and punches, 5 inches long and 3/8 inch diameter, forged from high-grade tool steel, hardened, ground and tempered, with polished points. Supplied in leather-cloth case, with tools held in place by a leather strap.
DRAWING OUTFIT, Mechanical—A practical and serviceable outfit for miscellaneous drawing work. The instruments are of substantial construction and all materials are of dependable quality. The outfit will be found complete and will give excellent service.
DRILL, Hand—Having nickel plated chucks and cocobolo handles, holding drills from 0 to 3/16 inch, complete with 8 fluted points in hollow handle.
DRILL, Automatic Push—With magazine handle, with 8 drill points, each in a separate numbered compartment, from which they are released one at a time through hole in rotating cap. Substantially constructed. Exposed parts polished, nickel plated and buffed. Length over all, 10 inches. With 8 fluted drill points, 1/16 to 11/64 inch diameter. For modern drills, check out what we think is the best corded hammer drill and the best cordless drill for concrete.
HAMMER, Claw, Polished Steel—Weight, 13 oz.
HACK SAW, Adjustable—To hold any size blade from 8 to 12 inches. Without blade.
HACK SAW BLADES—Highest grade of extremely hard steel. Three sizes. We recently looked at the best hacksaw for metal.
LEVEL, Carpenters’, Stanley, 24 inch—Hardwood, size 3 1/8 by 1 3/8 inches, with brass tips. Two glasses one single plumb and one single level. Proved glasses.
PUNCH SET, Taper Pin—Consists of 8 assorted pin punches, 3/32 to 3/8 inch points, in handy, round wooden box. Punches are forged from octagon tool steel, 3/8 inch diameter, about 6 inches long, hardened, ground and tempered, with polished points.
SAW Hand Carpenters’, Disston—Straight back. Crucible steel, polished blade. Beechwood handle, full polished, with 4 brass screws. Length of cutting edge, 26 inches. Width of blade at butt, 6¾ inches ; width at point, 2¼ inches.
SCREW DRIVER—Yankee Spiral.
SCREW DRIVER, Pocket—Consists of hollow handle, with chuck, 3 small screw driver blades, 1/8, 3/16 and ¼ inch, and a reamer. When not in use the chuck and blades are contained inside the handle. The blades are made of tool steel, and the handle is polished, nickel plated and buffed. Length closed, 3¾ inches.
SCREW DRIVER—Strong and durable, with accurately ground tips. The handles are hardwood and nicely finished. The shank passes through the handle and ferrule and is pinned. The blades are made from selected steel, tempered and well finished.
SOLDERING OUTFIT—Consists of soldering iron, bar of solder, scraper and solder flux, packed in a neat box. Soldering copper weighs ½ pound.
STEEL SQUARE, Carpenters’—One piece weldless steel with plain cut markings. Of special analysis steel, tempered to the proper spring. The ends and corners are hardened. Body 24×2 inches ; tongue 16 x 1½ inches. Face marked 1/8, ¼, 1/8, ¼. Back marked ¼, ¼, ¼.
TRY SQUARE, Stanley—Polished rosewood handle with brass face plate and handy finger grooves. Blued and tempered steel blade. Stamped figures and lines graduated to 1/8 inch. Length of blade, 6 inches ; length of handle, 4 5/8 inches.
TOOL SET, Complete—Cabinet made of oak, finished in dark stain on the outside and in a light stain on the inside. Joints notched and glued. With three hinges, two catches and a carrying handle. The hinged panel on the right, which carries the small tools, closes inside the front and back and makes a very compact cabinet. With the following 32 high-grade tools:
Dimensions of cabinet, 11¾ inches wide, 7 inches deep, 29 inches high. Net weight, 43 pounds; shipping weight, 62 pounds .
WRENCH, Monkey—One piece bar and head forged from special alloy steel. Hardened jaws. Machine cut screw with knurled head. Malleable handle frame and polished hardwood grips firmly riveted.
WRENCH, Stillson—Of special alloy, heat-treated steel, insuring added strength and gripping power. Hardened jaws. Polished shank, frame and jaws. Frame fastened to jaw by movable steel pin.
TRANSIT, Pocket, Mine, Brunton Patent, Improved Type—Within the limits of accuracy imposed by its size, this instrument can be used for taking courses, horizontal angles, vertical angles, or as a prismatic compass. Although designed as a hand instrument, it may be attached to a tripod for vertical angles or long tangents. The case is of aluminum alloy 2¾x2¾x1 1/8 inches, completely enclosing the instrument, and its size and weight (8 oz.) permits of it being easily carried in the vest pocket.
Unless otherwise ordered, instruments will be supplied with compass circles numbered in quadrants (0 to 90 each way), but 0 to 360 counterclockwise (circles reading azimuths N 0, E 90, S 180, W 270), or clockwise circles will be furnished without extra charge if specified.